We all have those blasted boob lights. I have 4 that I wanted to replace, but with my low ceilings, I needed something close to the ceiling. As I was shopping the Pottery Barn website, I came across the Mia Faceted-Crystal Flushmount Light
. It was lovely, but for $129 a piece, I'd be shelling out way more than I could stomach for 4 of them, even if I waited for a sale.
As I was admiring it, I noticed it was constructed very similarly to the boob lights I already had. I had a long string of acrylic crystals left over from redoing my dining room light, so I decided to DIY!!
Can of oil rubbed bronze spray paint
Nail and Hammer or Dremmel tool with metal drill bit
String of acrylic crystals (affiliate link)
Optional: yarn or string to help measure circumference
There's a small piece that screws on the bottom and holds up a metal circle that the dome rests on. Once I removed the glass dome (setting aside for a bird bath), I was able to remove the light from the ceiling and start putting holes in the outer edge to hold the end of each crystal strand.
First I removed he reflective foil.
One of my lights had some glue that needed to be goo goned. Then I taped the inside of the light socket so I could spray paint the bolt and socket oil rubbed bronze to match the rest of the fixture.
Looks good, but I should have waited to paint it after I drilled the holes. I wound up getting metal dust stuck in the freshly dried area and had to repaint to cover some scratches made.
I wanted to make 2 rows of 24 holes. (The holes would be across from each other to loop the wire strands through. I used a piece of string to measure the circumference and divided it by 24. I decided to round up and space the holes 1.25" apart, which made only 20 holes, but I figured it would be sufficient.
I made a piece of yarn 1.25" and used a Sharpie to mark where my outer holes would be.
I used a Dremel tool to make most of the holes, but near the end of the project, my bit was getting really dull and I ended up using a nail and hammer.
It worked a little easier and the holes were less messy.
For my second light I used solely a nail to make all the holes and it went super fast.
Next I needed to put holes in the metal circle.
I traced it on some paper to help figure out spacing and then imitated it with a Sharpie on the metal. I started with evenly putting dots for a pentagon (black dots). Then put a dot in the middle of each of those sections (red dots). And then put another dot in the middle of those sections (blue dots).
I separated my crystal strand into strings with 6 crystals.
I attached all the crystals to the small circle first.
Then I slipped it on the metal rod and started attaching around the outside.
When I was done, I screwed on the end piece, flipped it over and had a pretty looking light!
This one has crystals all the same size
This one has crystals of varying size
I love the way the light reflects the crystals.
Linking up to:
this is a great diy!ReplyDelete
Love the Mia lights! You did an incredible job copying them.ReplyDelete
Boob light! LOL! Yes, I'm 12.ReplyDelete
Fantastic idea! I would love it if you joined and contribute your awesome posts at my link party at City of Creative Dreams, starts on Fridays :D Hope to see you there at City of Creative Dreams Link Party.ReplyDelete
This looks great! But how do you change the light bulb?ReplyDelete
The light bulb easily fits in between the crystal strands. (The strands aren't stiff and move if you touch them).Delete
So do you use a clear bulb now?ReplyDelete
Yes, I put clear bulbs in. They look so much better!Delete
Clever idea... I have one of these lights... the before version! ha ha... I should make one of these, so cute!ReplyDelete
where did you get your crystals?ReplyDelete
I got them off Amazon! http://www.amazon.com/Faux-Crystal-Garland-CrystalPlace-30/dp/B0049X83LW/ref=sr_1_8?ie=UTF8&qid=1421695795&sr=8-8&keywords=crystal+string&pebp=1421695819839&peasin=B0049X83LWDelete
Hi Emily! I work with Cassity over at Remodelaholic, and we LOVE this! We'd love to feature you -- email me at email@example.com and we can discuss the details!ReplyDelete
Hi - this project I awesome and is something I'd lie to do. I see the holes you made for the crystal strands, but what I'd like to know is HOW you attached the strands to the holes???ReplyDelete
The strands of crystals have metal links that are kind of like key rings. I just looped one of the metal loops through the hole.Delete
Awesome fixture! How did you make your holes in the small metal circle that sits at the bottom? Did you use a nail & hammer? If so, would you recommend this or another way?ReplyDelete
Yes, I used a nail and hammer on hard surface (I did it on concrete). It worked really well.Delete